| Are you having trouble installing LED under car | | | | determine a location inside your vehicle to mount |
| lights onto your vehicle? Or maybe your just not | | | | the digital control panel. You want it to be in a |
| sure where all the wires for the under car lights | | | | location where you can easily access all its |
| go? Let us show you all the "in's & out's" of this | | | | buttons and functions while your sitting in the |
| type of installation - which i should mention, is | | | | vehicle.The LED under car lights distribution block |
| designed with the "Novice" in mind.The first thing | | | | and the control panel can be hooked together |
| you'll need to do when installing LED under car | | | | using the ribbon wire that comes with your |
| lights, is to find where you want to mount the led | | | | particular kit. The wire needs to be pushed |
| tubes. Be sure to keep their location in mind while | | | | through a hole in the firewall and plugged into the |
| doing the wiring part of the installation, so you can | | | | "input" on the side of distribution block. For those |
| allow for the correct lengths of the wires.It is ideal | | | | of you who may be a bit confused as to what |
| to mount the led tubes so as they are centered | | | | the firewall is, it's the wall that divides the engine |
| between the overall length of the vehicle for | | | | compartment and the interior of the vehicle. Be |
| optimal appearance. Tubes should be positioned on | | | | careful when you do this because the wire |
| the chassis of the vehicle so as they are not | | | | adaptors are fragile.The power wire on the digital |
| visible. Visible led car lights are prohibited by law in | | | | control panel can be connected directly to the |
| most cities.You'll now need to disconnect the | | | | Positive side of the car battery or to any 12V |
| battery before starting on the installation and the | | | | power wire under the dashboard. There will also |
| drilling of holes. Do this by disconnecting the | | | | be an "Earth wire" or Negative ground wire |
| negative battery cable. This led under car lights | | | | coming out from the control panel that will need |
| installation involves disconnecting the battery first | | | | to be securely screwed to the chassis of the |
| and foremost for safety reasons, and so you | | | | vehicle or to any "Earth wire" to complete the |
| don't "short-out" your car wiring.The easiest way | | | | power circuit.Finally, to be able to operate your |
| to mount the LED tubes is to start the screws in | | | | LED under car lights, the included switch and fuse |
| the brackets first,(supplied in kit) then holding the | | | | should be connected between the control panel |
| bracket in place, insert and tighten the screws | | | | and the power supply. All you need to do now is |
| into the holes. Make sure that the wires coming | | | | to plug all the LED tubes into the Distribution block, |
| from the *Side* tubes are facing the front of the | | | | complete any additional wiring according to your |
| vehicle. It's best to tighten the screws just | | | | kit instructions and then you'll be all set to show |
| enough to hold the bracket in place, then go back | | | | em off!Please see our "More-In-depth" and |
| after once you almost finished and individually | | | | step-by-step picture illustrated instructions on the |
| tighten each one until it seats firmly.You should | | | | How to install page listed below.Antonio Gabellone |
| have a distribution block in your under car lights | | | | is the Owner/Author of - The Site is a great |
| kit, find a good location for the block on a flat | | | | resource aimed at Neon Car Lights from |
| surface in the engine compartment away from | | | | PlasmaGlow with "life-time Warranties". |
| any heat or moving parts.Next you will need to | | | | |